People set up Netgear routers in their homes to stay connected to a lag-free or super-speedy internet connection. With that being said, doing Netgear Nighthawk router setup has become a common task these days. But, there are times when users face issues while using their devices. One of them is the IP-fluctuation problem. Various complaints have been reported where users have stated that their Netgear router keeps changing IP. Are you also facing the same problem? If yes, then walk through the information jotted down in this post. Here, we will reveal the reasons along with the troubleshooting techniques that can help you resolve the IP-related problem easily.
Let’s Start with Rebooting
The first thing you are suggested to do in this case is to reboot the router. This is because when the router doesn’t boot up properly, its chances of getting the IP address from the modem decreases. Thus, you can re-initiate the IP allocation process by rebooting the router. The steps to reboot the router have been mentioned below:
- Disconnect all the devices connected to your Netgear Nighthawk router.
- After that, pull the router’s plug out of its respective wall outlet.
- Wait for fifteen minutes and then connect the router back to its power outlet.
- Reconnect it to the modem and other devices.
Now, check whether your Netgear router keeps changing the IP address or not. If it does, you are suggested to move to other hacks mentioned below.
Solutions: Netgear Router Keeps Changing IP Address
1. Ensure Stable Power Supply
If the power being supplied to your Netgear Nighthawk router is not stable, then also there are chances of IP fluctuations. Do you know why? This is because when the router is not getting a stable power supply, it gets stuck in a reboot loop. Hence the modem fails to allocate a particular IP address. Therefore, you are required to check the power socket to which you’ve connected your Netgear router. It is supposed to be free of damages. Apart from this, the power of the router is also supposed to be well-working.
Note: Just in case you live in an area that suffers power outages, we recommend you use a UPS to power up the WiFi router. It will suffice the power requirements.
2. Use a Non-Damaged Ethernet Cable
The Netgear router and modem share a wired connection. In light of the same thing, the physical status (condition) of the Ethernet cable status decides whether the router will get an IP address from the modem or not. If the cable connecting your Nighthawk router to the modem is found damaged, you shouldo replace it with a new one. The reason being, using a damaged Ethernet cable will result in internet-related problems that can even stop you from accessing the routerlogin.net setup URL. Apart from being non-damaged, the cable used by you must be connected to the correct ports of your WiFi devices.
3. Update the Firmware Version
The firmware version on which your Netgear router is running must be updated. There are times when the router fails to obtain an IP address due to this very reason. Wondering why? Know that it is the firmware that controls how your router behaves. It means it controls everything including the hardware and software behavior of the router. Therefore, there are high-chances that the router is not getting the IP address because of an outdated firmware version. Therefore, we recommend you install the latest firmware version on the router by accessing the router login portal. You can also flash the firmware via TFTP.
Quick Tip: The Netgear router might also fail to get the IP address of the modem if the latter’s network is overburdened. In simple words, the network of the modem is so occupied that there is no room for the router to get connected and obtain an IP. So, you are suggested to disconnect a few devices from the network of your modem and check if the problem resolves.
The Concluding Thought
Many users are unable to make the most of their home networks because their Netgear router keeps changing the IP address. Keeping them in mind, we penned down the post. We are now anticipating that after taking the help of the tips given in the post, you will be able to get rid of the IP-fluctuation issue. Just in case nothing has worked in your favor, reset the router and set it up once again using the Netgear Nighthawk app.